Rewiring and new circuit installation in Conyers, GA means replacing aging or unsafe wiring throughout a home, or running dedicated circuits to support appliances, additions, and outbuildings that your existing panel and wiring were never sized to handle.
If your Conyers home has aluminum wiring from the 1970s, two-prong outlets in every room, or a panel that trips the moment you run the microwave and the air conditioner at the same time, those are signs the electrical system hasn’t kept up with how you actually live. A rewire or a new circuit run corrects the problem at the source, not just the symptom. Rockdale County requires permits and inspections for this work, and a licensed electrician pulls those for you.
All Purpose Heating and Air Conditioning has been doing this work in the Atlanta metro for more than 35 years. Conyers is about 30 minutes east on I-20, and our crews make that run regularly. We know the housing stock here, from the older homes near Olde Town to the 1980s and 90s ranch and split-level subdivisions scattered across the county, to the newer builds going up along the Salem Road corridor.
Whether you need one new circuit for a chest freezer in the garage or a full rewire on a house that still has its original wiring, we can take a look and tell you exactly what the job involves. Request your estimate and get a straight answer.
The trigger is usually something specific: a breaker that won’t stay reset, outlets that won’t accept a three-prong plug, or a renovation that’s about to add square footage the current wiring can’t support. A few situations come up often in Conyers homes.
Older wiring that’s past its useful life. Homes in and around Olde Town Conyers and the Milstead area frequently have aluminum branch-circuit wiring or, in the oldest cases, knob-and-tube. Aluminum wiring requires specific devices and connection methods to reduce fire risk. Knob-and-tube has no ground conductor and no protection against today’s electrical loads. Two-prong outlets throughout a house are the visible sign of a system that was built for a different era.
A renovation or addition. Adding a room, finishing a basement, or converting a detached garage into a workshop means new circuits. The larger lots common toward the Rockdale County line often include outbuildings that were wired with an undersized feed decades ago. Running a proper subpanel and dedicated circuits to a detached garage or shop is a common job for us.
A new load that needs its own circuit. A hot tub, a pool pump at a property near Black Shoals Park, an EV charger, a kitchen appliance like a double oven or an induction range, a chest freezer, or a workshop compressor all need a dedicated circuit. Plugging them into a shared circuit is what causes nuisance tripping and, eventually, real damage.
If any of these sound familiar, the next step is a look at your panel and a conversation about what the fix actually involves.
Every job starts with an inspection. We look at the panel, trace what’s already there, and identify what needs to go. For a full rewire, that means walking every room. For a new circuit, it means understanding where the load is, where the panel is, and what’s between them.
From there, we plan the runs. In a finished home, that means deciding how to route wire with the least disruption to walls and ceilings. An unfinished basement or an attic with open joists makes the job faster and less invasive. A fully finished two-story with plaster walls takes more time and more care. That difference in access is one of the biggest factors in what a job costs and how long it takes.
Permits come before wire gets pulled. Rockdale County requires an electrical permit for rewiring and new circuit work, and the job ends with a county inspection. We pull the permit, schedule the inspection, and make sure the work is done to code before that inspector shows up. This protects you when you sell the house and protects your homeowner’s insurance in the meantime.
Once the permit is in hand, we pull the wire, install boxes and devices, connect at the panel, and test everything. If drywall needs to be cut to run wire, we coordinate patching so you know what to expect. We don’t leave you with open walls and a list of other contractors to call.
What drives cost on this type of job: the number of circuits, the square footage being served, how much of the home is finished versus open, and the permit fee. Request your estimate to get a real number for your specific house.
Rewiring and new circuits are one part of what we do for Conyers homeowners. If your project starts with a wiring conversation but leads somewhere else, we can handle that too.
If you’re not sure whether rewiring is the right call or you just want to understand the full picture of your home’s electrical system, our electrical services page for Conyers, GA covers the range of work we do in this area, from service calls to larger projects.
If rewiring comes with the realization that your panel is undersized or aging out, that’s a separate but related job. Our panel upgrade service for Conyers homeowners explains what’s involved in replacing a panel and when it makes sense to do it at the same time as a rewire.
And if you want to read more about what rewiring and new circuit installation involves as a service, our rewiring and new circuits service page covers the technical side in more detail.
We also serve homeowners in Atlanta, Alpharetta, Peachtree City, Newnan, and McDonough. If you’re in Conyers or anywhere in Rockdale County, give us a call or request your estimate and we’ll get you on the schedule.
+
