Outlets, switches, and lighting services in Atlanta, GA cover the installation, repair, and replacement of the receptacles, wall switches, light fixtures, ceiling fans, and safety devices throughout your home. If you have a dead outlet, a switch that does nothing, or a kitchen that still lacks GFCI protection, this is the work that fixes it.
Atlanta’s housing stock is one of the most varied in the South. On one block in Virginia-Highland or Inman Park you might have a 1920s bungalow with original two-prong receptacles and wiring that has never been touched. Two streets over, a townhome built in the last decade has builder-grade devices that are starting to fail. The age and condition of what’s behind your walls shapes every part of the job, from what devices we can install to whether a new circuit is needed to do it safely.
All Purpose Heating & Air Conditioning has had crews working across Atlanta every day for more than 35 years. We are locally owned, licensed, and insured, and we handle residential electrical work the same way we handle everything else: show up, assess what’s actually there, and fix it right.
If something in your home isn’t working the way it should, or you want to add lighting, fans, or receptacles that aren’t there yet, give us a call or request your estimate and we’ll take a look.
Some calls are obvious. An outlet sparks when you plug something in, or the cover plate is warm to the touch. Both are signs that something is wrong behind the wall, and neither is a situation to watch and wait on. In older intown neighborhoods like Grant Park or the West End, homes built in the early to mid-1900s sometimes still have original wiring that was never designed to carry the load a modern household puts on it. Warm outlets and nuisance trips are often the first sign that the wiring or the device itself has reached the end of its useful life.
Other calls come from homeowners who simply don’t have enough outlets. A bedroom with two receptacles, a kitchen with no GFCI protection near the sink, a bathroom where the only outlet is on the wrong wall. Code has required GFCI protection in kitchens, bathrooms, garages, and exterior locations for decades, but plenty of Atlanta homes predate those requirements and have never been updated.
Lighting is a big part of this work too. Homeowners add recessed lighting to a living room or kitchen, replace a dated flush-mount with a ceiling fan, or want exterior lighting on a detached garage or along a back fence. In older homes, adding recessed lights or a ceiling fan often means working with plaster ceilings or attic access that complicates the job. In newer construction, the wiring is more accessible but the builder-grade fixtures and switches are often the first things homeowners want to change.
Atlanta’s long, hot summers also drive demand for ceiling fans. A well-placed fan in a bedroom or screened porch makes a real difference from May through September, and installing one correctly, with a rated ceiling box and proper wiring, is not a DIY job in most homes.
Every job starts with an assessment. We look at what you have, what you want, and what the wiring behind the wall will actually support. In a 1940s bungalow, that assessment might turn up aluminum wiring, undersized circuits, or two-prong receptacles with no ground path. In a newer home, the wiring is usually fine but the devices or fixture boxes may not be rated for what the homeowner wants to install. We tell you what we find before we start work.
Device selection comes next. For a straight replacement, we match the device to what code requires for that location. GFCI receptacles in kitchens, bathrooms, garages, and exterior locations. AFCI protection on bedroom circuits where current code applies. Tamper-resistant receptacles in homes with young children. These aren’t upsells. They’re what the job requires done correctly.
Wiring and installation follow the assessment. We run new wire where it’s needed, replace devices, mount fixtures, and make clean, secure connections throughout. If a new circuit is required, we pull the permit and schedule the inspection.
Before we leave, we test everything. Every outlet gets checked for proper wiring, ground, and polarity. Every GFCI gets tripped and reset. Every switch and fixture gets cycled.
What drives the cost and timeline on these jobs: the number of devices being replaced or added, whether new circuits are needed, how accessible the ceiling or wall cavities are, and the cost of the fixtures themselves. A single outlet swap is a short visit. A whole-house GFCI update or a multi-room lighting project takes longer. The only way to get a real number for your specific job is to request your estimate.
All Purpose Heating & Air Conditioning works across Atlanta and the surrounding area. Whether you’re in Buckhead, Midtown, East Atlanta, or one of the neighborhoods farther out, we have crews in the area regularly and can get to you without the long lead times you might expect from a larger, less local operation.
If you want to learn more about what our electricians do across the city, our Atlanta electrician services page covers the full scope of residential and commercial electrical work we handle here. For a closer look at outlets, switches, and lighting specifically, the outlets, switches, and lighting service page walks through the most common jobs and what to expect from each one.
Older Atlanta homes in particular often need more than just new outlets. If your home is running on an original panel or one that hasn’t been updated in decades, the outlet and lighting work you want may point to a bigger underlying issue. Our panel upgrade page for Atlanta explains what drives that work and when it makes sense alongside a device update.
We also serve Alpharetta, Conyers, Peachtree City, Newnan, and McDonough. If you’re outside Atlanta proper, give us a call and we’ll let you know what scheduling looks like for your area. Request your estimate and we’ll get started.
+
